This page no longer updated from 31 October 2001. Latest version can be found at Apollo LRV

Other Designations: Lunar Roving Vehicle. Class: Manned. Type: Lunar Lander. Nation: USA.

The Apollo Lunar Roving Vehicle was one of those sweet pieces of hardware that NASA and its contractors seemed to be able to develop so effortlessly during the short maturity of the Apollo programme. The collapsible 208 kg battery-powered rover could take two astronauts, 55 kg of scientific equipment, and 27 kg of lunar samples over a cumulative distance of 92 kilometres during one lunar day. The Lunar Rover was the only piece of equipment from NASA's ambitious post-Apollo lunar exploration plans to actually fly in space.

Weighing about 208 kilograms (457 pounds), Earth weight when deployed on the Moon, the LRV could carry a total payload of about 490 kilograms (1,080 pounds), more than twice its own weight. The payload included two astronauts and their portable life support systems (about 353 kilograms; 800 pounds), 45.4 kilograms (100 pounds) of communications equipment, 54.5 kilograms (120 pounds) of scientific equipment and photographic gear, and 27.2 kilograms (60 pounds) of lunar samples.

The LRV was designed to operate for a minimum of 78 hours during :the lunar day. It could make several exploration sorties to a cumulative distance of 92 kilometres (57 miles). The maximum distance the LRV was permitted to range from the lunar module was approximately 9.7 kilometres (six miles), the distance the crew could safely walk to the LM in the unlikely event of a total LRV failure. This walk-back distance limitation was based upon the quantity of oxygen and coolant available in the astronauts' portable life support systems. This area contained about 290 square kilometres (113 square miles) available for investigation, 10 times the area that could be explored on foot.

The vehicle could negotiate obstacles 30.5 centimetres (one foot) high, and cross crevasses 70 centimetres wide (28 inches). The fully loaded vehicle could climb and descend slopes as steep as 25 degrees, and park on slopes up to 35 degrees. Pitch and roll stability angles were at least +-45 degrees, and the turn radius was three meters (10 feet).

Both crewmen sat so the front wheels were visible during normal driving. The driver used an on-board dead reckoning navigation system to determine direction and distance from the lunar module, and total distance travelled at any point during a traverse.

The LRV consisted of five major systems: mobility, crew station, navigation, power, and thermal control. Secondary systems included the deployment mechanism, LM attachment equipment and ground support equipment.

The aluminium chassis was divided into three sections that supported all equipment and systems. The forward and aft sections fold over the centre one for stowage in the LM. The forward section held both batteries, part of the navigation system, and electronics gear for the traction drive and steering systems. The centre section held the crew station with its two seats, control and display console; and hand controller. The floor of beaded aluminium panels could support the weight of both astronauts standing in lunar gravity. The aft section held the scientific payload.

Auxiliary LRV equipment included the lunar communications relay unit (LCRU) and its high and low gain antennas for direct communications with Earth, the ground commanded television assembly (GCTA), a motion picture camera, scientific equipment, tools, and sample stowage bags.

Mobility System

The mobility system was the major LRV system, containing the wheels, traction drive, suspension, steering, and drive control electronics subsystems.

The vehicle was driven by a T-shaped hand controller located on the control and display console post between the crewmen. Using the controller, the astronaut manoeuvred the LRV forward, reverse, left and right.

Each LRV wheel had a spun aluminium hub and a titanium bump stop (inner frame) inside the tire (outer frame). The tire was made of a woven mesh of zinc-coated piano wire to which titanium treads were riveted in a chevron pattern around the outer circumference. The bump stop prevented excessive inflection of the mesh tire during heavy impact. Each wheel weighed 5.4 kilograms (12 pounds) on Earth and was designed to be driven at least 180 kilometres (112 miles). The wheels were 81.3 centimetres (32 inches) in diameter and 22.9 centimetres (nine inches) wide.

A traction drive attached to each wheel had a motor harmonic drive gear unit, and a brake assembly. The harmonic drive reduced motor speed at an 80-to-1 rate for continuous operation at all speeds without gear shifting. The drive had an odometer pickup (measuring distance travelled) that sent data to the navigation system. Each motor developed 0.18 kilowatt (1/4-horsepower) and operated from a 36-volt input.

Each wheel had a mechanical brake connected to the hand controller. Moving the controller rearward de-energised the drive motors and forced brake shoes against a drum, stopping wheel hub rotation. Full rear movement of the controller engaged and locked a parking brake.

The chassis was suspended from each wheel by two parallel arms mounted on torsion bars and connected to each traction drive. Tire deflection allowed a 35.6-centimeter (11-inch) ground clearance when the vehicle was fully loaded and 43.2 centimetres (17 inches) when unloaded.

Both front and rear wheels had independent steering systems that allowed a "wall-to-wall" turning radius of 3.1 meters (122 inches), exactly the vehicle length. If either set of wheels had a steering failure, its steering system could be disengaged and the traverse could continue with the active steering assembly. Each wheel could also be manually uncoupled from the traction drive and brake to allow "free wheeling" about the drive housing.

Pushing the hand controller forward increased forward speed; rear movement reduced speed. Forward and reverse were controlled by a knob on the controller's vertical stem. With the knob pushed down, the controller could only be pivoted forward; with it pushed up, the controller could be pivoted to the rear for reverse.

Crew Station

The crew station consisted of the control and display console, seats, seat belts, and armrest, footrests, inboard and outboard handholds, toeholds, floor panels, and fenders.

The control and display console was separated into two main parts: The top portion held navigation system displays; the lower portion contained monitors and controls. Attached to the upper left side of the console was an attitude indicator that showed vehicle pitch and roll.

At the console top left was a position indicator. Its outer circumference was a large dial that showed vehicle heading (direction) with respect to lunar north. Inside the dial were three digital indicators that showed bearing and range to the LM and distance travelled by the LRV. In the middle of the console upper half was a Sun compass device that was used to update the LRV's navigation system. Down the left side of the console lower half were control switches for power distribution, drive and steering, and monitors for power and temperature. A warning flag atop the console was set whenever a temperature went above limits in either battery drive motor.


Apollo LRV Chronology

11 July 1966 NASA leaders make several significant program decisions affecting AAP and post-Apollo development planning.

Meeting at Headquarters, Deputy Administrator Robert C. Seamans, Jr., Associate Administrator for Manned Space Flight George E. Mueller, and Associate Administrator for Space Science and Applications Homer E. Newell made several significant program decisions affecting AAP and post-Apollo development planning in general: MSFC would be the lead Center for developing the ATM and would be responsible for all astronomy experiments. MSFC would be the lead Center for 'lunar engineering'-i.e., design and development of lunar exploration vehicles (including surface modules, supply trucks, and roving vehicles). MSC would have responsibility for Earth resources and lunar scientific experiments.

15 January 1969 Guidelines for Apollo missions after first landing Program: Apollo.

The Apollo Program Director expressed concern to the Director of MSC over the lack of guidelines of sufficient scope and depth for the lunar missions that would be flown after the first lunar landing and before the proposed lunar exploration program tentatively scheduled to begin in 1973. He asked each of the manned space flight Centers to appoint a working group to define guidelines and to outline program objectives and content for the period of lunar exploration immediately following the first lunar landing. Areas requiring study were: scientific exploration, mission planning rationale, flight schedules and program impact, and vehicle product improvement.

27 May 1969 Manned Apollo lunar roving vehicle go-ahead Program: Apollo.

MSFC was authorized to proceed with development of a manned lunar roving vehicle for use on the Apollo missions beginning in mid-1971. A meeting was scheduled for June 6 in Washington to establish requirements for development of the vehicle.

20 June 1969 Requirements for the Apollo lunar roving vehicle (LRV) design Program: Apollo.

Christopher C. Kraft, Jr., MSC Director of Flight Operations, recommended that the following fundamental requirements be considered during the lunar roving vehicle (LRV) design approach: "a. A means of continuous voice communication with one crew member, on or off the LRV to the mother station (LM) and from the mother station to earth, must be provided. b. A simple dead reckoning system should be considered for determining the LRV and crew location at all times in order to provide a safe return of the astronauts to the LM. The accuracy should be sufficient to permit the astronauts to rendezvous with the LM from any point on a sortie. c. The vehicle should be designed so that a telemetry system is not required for operation. However, for crew safety and systems operations, instrumentation may be required."

07 August 1969 Apollo lunar roving vehicle restricted to a 181-kilogram weight limit Program: Apollo.

MSFC-NASA Hq. correspondence emphasized the need to restrict the lunar roving vehicle to a 181-kilogram weight limit. If necessary, range and speed would be traded off to retain this weight limit.

18 August 1969 Apollo Lunar Roving Vehicle Task Team reconstituted as the Lunar Mobility Task Team Program: Apollo.

The Lunar Roving Vehicle Task Team, which had been established at MSFC on April 7, was reconstituted as the Lunar Mobility Task Team. Its function would be to direct and coordinate MSFC efforts to conceive, design, and develop various modes of lunar transportation systems.

26 August 1969 Primary batteries should be used to power the Apollo lunar roving vehicle Program: Apollo.

In response to a query from MSFC, MSC took the position that primary batteries as opposed to secondary (rechargeable batteries) should be used to power the lunar roving vehicle. Concern was expressed that a solar array recharge assembly would introduce an extra complexity into the LM payload packaging and the roving vehicle servicing requirements and would contribute to a loss in effective EVA time because astronauts would need time to deploy the solar array and connect it to the rover.

28 October 1969 Apollo lunar roving vehicle (LRV) contract awarded to the Boeing Program: Apollo.

A lunar roving vehicle (LRV) cost-plus-incentive-fee contract was awarded to the Boeing Co. LRV-1 was scheduled for delivery on April 1, 1971, leaving only 17 months for vehicle development, production, and tests. The LRV project was managed at MSFC by Saverio F. Morea as a project within the Saturn Program Office. The Boeing Company would manage the LRV project in Huntsville, Ala., under Henry Kudish. General Motors Corp. AC Electronics Defense Research Laboratories in Santa Barbara, Calif., would furnish the mobility system (wheels, motors, and suspension). The Boeing Go. in Seattle, Wash., would furnish the electronics and navigation system. Vehicle testing would take place at the Boeing facility in Kent, Wash., and the chassis manufacturing and overall assembly would take place at the Boeing facility in Huntsville, Ala.

06 November 1969 Concern over weight growth of the Apollo lunar roving vehicle Program: Apollo.

In an exchange of correspondence between MSFC and MSC concern was expressed over the weight growth of the lunar roving vehicle (LRV) and its payload. As a result, a recommendation was made that MSFC manage the weight of the LRV and MSC the payload weight.

01 December 1969 Requirement for a simple lightweight Apollo lunar roving vehicle guidance and navigation system Program: Apollo.

The MSC Flight Crew Operations Directorate submitted its requirement for a simple lightweight Rover (lunar roving vehicle) guidance and navigation system that would provide the following displayed information to the crew: vehicle heading and heading to the LM, speed in kilometers per hour, total distance traveled in kilometers, and distance to the LM. Requirements were based on the assumptions that the landing area was as well known as for Apollo 12, all traverses were preplanned, accurate photo maps were available, and there was MSFN support through voice communications. The Directorate emphasized that it had no requirements for a display of pitch and roll, X and Y coordinates, or time.

16 December 1969 Apollo lunar roving vehicle preliminary requirements review Program: Apollo.

A lunar roving vehicle preliminary requirements review was held at MSFC. MSC was asked to review the requirement for a roll bar which it had requested in the interest of astronaut safety. Navigation system requirements as defined by MSC would require changes in the design presented by Boeing. Full-length fenders and effects of dust on radiators, sealed joints, and vision needed to be considered and appropriate measures taken in the vehicle design, the review found.

06 February 1970 Requirements for Apollo lunar roving vehicle (LRV) established Program: Apollo.

A statement of agreements was reached between NASA Hq. and the Centers covering the requirements for a lunar roving vehicle (LRV). Appropriate portions of the agreements were being incorporated in a revised Apollo Program Specification and in Apollo Program Directive No. 4.

11 September 1970 Modifications were made to Apollo lunar roving vehicle simulator to eliminate extreme fatigue Program: Apollo.

Modifications were made in MSFC's lunar roving vehicle simulator and the static mockup to eliminate extreme arm and hand fatigue felt by a flight crew member and other test subjects after driving 10 to 15 minutes in LRV simulator evaluation tests. A T-shaped handle was added to the pistol grip; a parking-brake release and a reduced brake-travel distance were incorporated; and a mechanical reverse lockout was added.

22 February 1971 MSC requested removal of sharp corners from the Apollo lunar roving vehicle (LRV) seat Program: Apollo.

MSC requested removal of sharp corners from the lunar roving vehicle (LRV) seat. During a recent series of LRV/EMU (extravehicular mobility unit) tests, a nicking or tearing of the portable life support system thermal cover had been discovered. Observation revealed that the thermal cover was contacting sharp corners on the LRV seats, when the test subject entered and left the vehicle.

01 March 1971 Automatic deployment system for the Apollo lunar roving vehicle abandoned Program: Apollo.

Because of difficulties during the past several months in developing and qualifying an automatic deployment system for the lunar roving vehicle, the automatic system was abandoned in favor of a manual system. Boeing was directed to stop all further effort on the automatic system.

26 July 1971 LRV-1 Program: Apollo. Launch Site: Cape Canaveral . Launch Vehicle: Saturn V.
01 August 1971 EVA Apollo 15-3 Program: Apollo. Flight Crew: Scott, Irwin.

Drove in lunar rover to Hadley Delta.

02 August 1971 EVA Apollo 15-4 Program: Apollo. Flight Crew: Scott, Irwin.

Drove in lunar rover to Hadley Rille.

18 November 1971 Detailed assessment of the lunar roving vehicle (LRV) used on the Apollo 15 mission Program: Apollo.

A detailed objective assessment of the lunar roving vehicle (LRV) used on the Apollo 15 mission indicated:

16 April 1972 LRV-2 Program: Apollo. Launch Site: Cape Canaveral . Launch Vehicle: Saturn V.
22 April 1972 EVA Apollo 16-2 Program: Apollo. Flight Crew: Young, Duke.

Drove in lunar rover to Stone Mountain.

23 April 1972 EVA Apollo 16-3 Program: Apollo. Flight Crew: Young, Duke.

Drove in lunar rover to North Ray crater.

07 December 1972 LRV-3 Program: Apollo. Launch Site: Cape Canaveral . Launch Vehicle: Saturn V.
12 December 1972 EVA Apollo 17-2 Program: Apollo. Flight Crew: Cernan, Schmitt.

Drove in lunar rover to South Massif.

13 December 1972 EVA Apollo 17-3 Program: Apollo. Flight Crew: Cernan, Schmitt.

Drove in lunar rover to North Massif.


Back to Index
Last update 12 March 2001.
Contact Mark Wade with any corrections or comments.
Conditions for use of drawings, pictures, or other materials from this site..
© Mark Wade, 2001 .